Modem-converter E1-L/S
(1U for 19")Specifications
Documentation
Modem E1-L/S (1U high version for 19 inch rack)
|
Features:
- ITU-T G.703, G.704, G.706 and G.823 compliant
- Up to 2 km
- CAS and CRC4 multiframing
- Ethernet or V.35/RS-530/RS-449/RS-232 user data interface
- Full duplex synchronous mode
- Selectable data rates
- Digital port loopback, local and remote link loopbacks
- Integrated BER tester
- Supervisory (console) RS-232 port
- Dry contacts alarm interface
- Construction: 1U high unit for 19 inch cabinet
- 220 VAC or 48/60 VDC power
- Certificate
|
The E1-L is a fractional E1 access device, for transmitting digital
data over framed (ITU-T G.704) E1 channels.
Digital data port rates are selectable for any multiple of 64 kbps
up to 1984 kbps. User data occupies only the required number
of E1 frame timeslots reducing billing to only bandwidth used.
E1-L also supports unframed E1 channels.
E1-L/S device may be ordered with
Ethernet, V.35 or multistandard digital interface.
The multistandard interface
is cable-switchable to RS-232, RS-530, RS-449 or V.35 standards.
The V.35 interface uses standard M34 female connector.
Devices may be AC or DC powered (176 to 264VAC at 50Hz or 36 to 72VDC).
Device operation may be controlled via console port (RS-232 port for
supervisory terminal connection).
With lack of the front panel controls or DIP switches E1-L/S device may be configured
and controlled from console only. When in framed mode of operation, the remote login
feature for access the remote E1-L/S or E1-XL device's console is available
for E1-L/S device.
So-called monitoring channel is used (in framed mode only) for accessing the remote
device status information and for remote login operation. The Sa4 bit of
the timeslot 0 of the E1 frame is used for the monitoring channel operation
(according to the ITU-T G.704 Recommendation). In addition, any bit of any timeslot
may be assigned for the monitoring channel operation for E1-L/S device.
The state of the E1-L/S device may be monitored by SNMP protocol via
IP network. The desired Sa bit for monitoring channel operation may be
assigned by the SNMP for and E1-L/S device.
Currently available models are listed in Prices. Please, contact technical support if you are unsure which model to choose.
Specifications
E1 Interface |
---|
Line Code |
HDB3 or AMI |
Line Impedance |
120 Ohm (twisted pair) |
Receive Signal Attenuation Range |
from 0 to -43 dB |
Jitter Attenuator |
On receive, up to 120UIpp attenuation |
Frame Structure |
In acc. to ITU-T G.704. Unframed mode available |
Multiframing |
CRC4, CAS |
Frequency Offsets Adjustment |
Controlled slip buffers in receive path |
Connector Type (E1-L/B-ETV, E1-L/S) |
RJ-48 (female) |
Digital Interface |
---|
Data Rate |
up to 1984 kbps (framed Nx64 kbps), or up to 2048 kbps (unframed) |
Clock Signals Supported |
TXC, RXC, ETC, ERC |
Modem Control Signals |
DTR, DSR, CTS, RTS, CD |
Connector Type (multistandard interface) |
HDB44 (female) |
Connector Type (V.35 interface) |
M-34 (female) |
Ethernet Interface |
---|
Interface Type |
10/100Base-T |
Data Transfer Rate |
up to 1984 kbps (framed Nx64 kbps), or up to 2048 kbps (unframed) |
Mode |
100 Mbps full duplex, 100 Mbps half duplex, 10 Mbps full duplex, 10 Mbps half duplex, or autonegotiation |
Address Table Size |
15000 MAC addresses |
Maximum Packet Size |
1600 bytes, including MAC header |
Protocols |
Transparent or Cisco-HDLC bridging IEEE protocol, selected automatically |
Quality of Service |
8 priority levels |
VLAN Support |
In acc. to IEEE 802.1q |
Connector Type |
RJ-45 (female) |
Alarm Interface |
---|
Connector Type |
DB9 (male), 9 pins |
Relay Contact Current |
Up to 600 mA |
Relay Contact Voltage |
Up to 110 VDC or 125 VAC |
Console Port |
---|
Interface Type |
RS-232 DCE |
Serial Protocol |
Asynchronous 9600 bps, 8 bits/character, 1 stop bit, no parity |
Connector Type |
DB9 (female), 9 pins |
Diagnostics |
---|
Loopbacks |
Local and remote link loops, digital port loop, activated from console |
BER Tester |
Activated from console |
Remote Control |
---|
Remote Login |
Available E1-L/S |
SNMP-based Management |
Device state monitoring, Sa bit assignment |
Physical (E1-L/S) |
---|
Dimensions |
444 mm x 262 mm x 44 mm |
Weight |
3400 g |
Power Source |
---|
AC Power Source |
176 to 264 VAC, 50 Hz |
DC Power Source |
36 to 72 VDC |
Power Consumption |
20 VA Max |
Environment |
---|
Temperature |
0 to 50 °С |
Relative Humidity |
0 to 80 %, non-condensing |
Documentation
Some of the documents are in Adobe® Acrobat® Reader® format
E1-L/S User's Manual in Russian
E1-L/S User's Manual in English
MIB files for SNMP management
Cronyx interface cables guide
Return to G.703 Interface Converters or Digital Communication Equipment
Copyright © 1996-2024 Cronyx